Buradasınız: Anasayfa - Takım tezgahı probları ve yazılımı - Ürün Listesi - TS27R

TS27R dokumalı takım ayar probu

Bu sayfa şu anda sizin dilinizde mevcut değildir. Google'ın Çeviri sistemini kullanarak otomatikleştirilmiş çeviriye ulaşabilirsiniz. Bu hizmeti sağlamaktan sorumlu değiliz ve çeviri sonuçları tarafımızdan kontrol edilmemiştir.
Eğer daha fazla yardıma ihtiyaç duyarsanız lütfen bizim ile temasa geçiniz.

Sayfa içeriğiKarşıdan YüklemelerYerel ofisinizi arayınız Bize çevrimiçi ulaşın

TS27RThe industry-standard contact probe for tool setting and broken tool detection on vertical machining centres.

About TS27R

TS27RTS27R is mounted on the machine table. It enables the user to set tool length and diameter of rotating tools, and to carry out broken tool detection.

As with all Renishaw hard-wired probe systems, TS27R requires the MI 8 interface to convert probe signals into an acceptable form for the CNC machine control.

TS27R features and benefits

  • The standard tool setting probe for machining centres
  • Compact table mounting
  • Precise tool length and diameter measurement
  • Rotating tools can be checked without wear to the tool or stylus
  • Stylus is protected by a weak link, preventing probe damage in the event of a collision

TS27R specification

Specification  
Sense directions ±X, ±Y, +Z 
Weight 650 g (23 oz)
Transmission type

Hard-wired

Uni-directional repeatability (max 2 sigma at stylus tip)  1.0 µm (0.00004 in)

Trigger force

Lowest force

Highest force

 

1.3 N (4.6 ozf)

2.4 N (8.5 ozf)

Stylus overtravel

XY plane

+Z direction

 

±10°

5.5 mm (0.21 in)

Maximum recommended stylus length

Cranked stylus

27 x 33 mm (1.06 x 1.3 in)

Sealing IP X8
Mounting

12 mm (0.5 in) T-bolt (not supplied).

Optional spiral pins to allow accurate re-mounting.

Compatible interface

MI 8 /MI 8-4

Software for TS27R

Renishaw tool setting software allows you to set tool length and diameter offsets for single point and multiple point tools, perform in cycle broken tool detection and manual or automatic (programmed) positioning.

Alternative tool setters

NC4 non-contact system   OTS (twin probing)   TS32 with optical transmission

NC4-separate

 

 

 

 

NC4 is the latest generation of non-contact tool setter and our most compact design.

 

 

OTS

 

 

 

 

OTS uses an optical transmission method, allowing cable-free operation of the machine table.

OTS can also be used as part of a twin probe - single receiver - system.

 

TS32

 

 

 

 

TS32 is an optical alternative to the TS27R, however Renishaw recommends upgrading to the new OTS tool setter.

TS27R ordering information

TS27R probe and interface

Part number Description
A-2008-0397 TS27R full kit disk stylus, MI 8-4 interface
A-2008-0396 TS27R full kit square stylus, MI 8-4 interface
A-2008-0367 TS27R full kit disk stylus, MI 8 interface
A-2037-0366 TS27R full kit square stylus, MI 8 interface
A-2008-0368 TS27R kit disk stylus

TS27R replacement parts and accessories

Part number Description
A-2008-0388 TS27R probe and holder
A-2008-0382 Disc stylus ø12.7 mm (ø0.5 in)
A-2008-0384 Square stylus 19.05 mm x 19.05 mm (0.75 in x 0.75 in)
A-5003-5171 TS27R break stem kit
A-5003-0661 Break stem
A-2037-0020 MI 8 interface kit
A-2157-0001 MI 8-4 interface kit

Sonraki Adımlar

Eğer daha fazla bilgiye ihtiyacınız var ise veya fiyatlandırma sorgusu istiyor iseniz bizimle çevrimiçi iletişim kurunuz, veya alternatif olarak doğrudan yerel Renishaw ofisiniz ile görüşebilirsiniz.